12 Top Burettes for 2019

 

Eisco Labs BuretteTube Clamp Single High Strength Alloy - Spring Loaded Jaws - 78 Width Capacity Max 16mm Dia Rod

Eisco Labs Burette/Tube Clamp, Single, High Strength Alloy – Spring Loaded Jaws – 7/8″ Width Capacity, Max 16mm Dia. Rod

Eisco Labs Burette/Tube Clamp, Single, High Strength Alloy – Spring Loaded Jaws – 7/8″ Width Capacity, Max 16mm Dia. Rod - Spring loaded, high strength alloy jaws holds objects in place. Powder coated for long lasting finish. Holds objects up to 7/8″ width/diameter.

 

Burette PlasticAcrylic 25mL

Burette, Plastic/Acrylic 25mL

Burette, Plastic/Acrylic 25mL - Acid cleaning solutions or wire handled brushes are not at all. Each burette is individually calibrated to give maximum accuracy. The ph range of 1-14 is ideal and upto 5% w/w of acids or 30% bases can be used. This 25ml burette has a transparent acrylic body and a leakproof stopcock fitted with a self-lubricating ptfe plug. Cleaning always clean the burette with a mild solution of soap or detergent. The acrylic body is unaffected by dilute mineral acids and bases except hydrofloric acid and ammonium hydroxide. Caution this burette should not be exposed to organic solvents & alcohols cracking of the burette is likely if bent or struck sharply against a hard surface.

 

SEOH Buret Burette Clamp Single Spring Loaded

SEOH Buret Burette Clamp Single Spring Loaded

SEOH Buret Burette Clamp Single Spring Loaded - Strong die cast body. Spring loaded, rubber covered grips. About 6″ wide. Accepts rods upto 16mm. For single buret.

 

Eisco Labs Borosilicate Burette Straight Bore PTFE Stopcock - 50mL cap 010mL grad Class A tolerance

Eisco Labs Borosilicate Burette, Straight Bore, PTFE Stopcock – 50mL cap., 0.10mL grad., Class A tolerance

Eisco Labs Borosilicate Burette, Straight Bore, PTFE Stopcock – 50mL cap., 0.10mL grad., Class A tolerance - Eisco borosilicate burette, straight bore, ptfe stopcock, 50ml, class a burette these high quality borosilicate burettes are straight bore with interchangeable ptfe key stopcocks. Accuracy is per iso 385, din 12709.

 

Eisco Labs Research Grade Lab Starter Kit - Includes 24 Rod 8x5 Retort Base Beaker Tongs Crucible Tongs BuretteTest Tube Clamp Ring Stand and more

Eisco Labs Research Grade Lab Starter Kit – Includes 24″ Rod, 8″x5″ Retort Base, Beaker Tongs, Crucible Tongs, Burette/Test Tube Clamp, Ring Stand (and more)

Eisco Labs Research Grade Lab Starter Kit – Includes 24″ Rod, 8″x5″ Retort Base, Beaker Tongs, Crucible Tongs, Burette/Test Tube Clamp, Ring Stand (and more) - Test tube brush is 215cm in total length, the brush section is 100mm in length and 125mm in diameter flask tongs are 250mm in total length, have vinyl coated tips and has a maximum opening of 200mm spatula has both a spoon side and flat side, is a total of 150mm long, and has a maximum width of 20mm crucible tongs are 250mm in length and have a maximum opening of 200mm test tube tongs are 170mm in length and have a maximum opening of 70mm. Kit contains (1) base, (1) rod, (1) beaker tong, (1) tripod stand, (1) wire mesh for heating, (1) boss head, (1) lab clamp, (1) retort ring with boss head, (1) burette clamp double, (1) test tube holder, (1) test tube stand (z-shape), (1) test tube brush, (1) spatula. Ring clamp with boss head has and inner diameter of 76mm and an outer diameter of 91mm, the bosshead can accept rods up to 20mm in diameter burette clamp holds burettes with diameters up to 22mm (usually 100ml burettes) and is spring loaded with 100% powder coated parts. The base is 5″x8″ powder coated alloy to resist chemicals and rubber lined bottom to stabilize and prevent bench scratching rod is stainless steel and is 12mm in diameter bosshead holds 2 rods perpendicular to each other and will accept rods up to 24mm in diameter the boss head holds the lab clamp which has a maximum opening of 100mm and a minimum grip of 2mm both the bosshead and clamp are powder coated. Test tube/lab instrument rack will hold up to 17 objects (8) small holes have a diameter of 12mm, (6) medium holes have a diameter of 18mm, and (5) large holes have a diameter of 25mm the rack is powder coated and chemically resistant tripod is cast metal and is 190mm in height and has an inner diameter of 75cm and an outer max diameter of 12cm wire mesh is a square with 12cm sides and a 8cm diameter heating surface.

 

Humboldt H-8012 Burette Clamp V-Jaw Flat Steel Zinc-Plated with Plastisol-Coated Jaws 38 to 1-38 Jaw Opening 39602 Length

Humboldt H-8012 Burette Clamp, V-Jaw, Flat, Steel, Zinc-Plated with Plastisol-Coated Jaws, 3/8″ to 1-3/8″ Jaw Opening, 39602″ Length

Humboldt H-8012 Burette Clamp, V-Jaw, Flat, Steel, Zinc-Plated with Plastisol-Coated Jaws, 3/8″ to 1-3/8″ Jaw Opening, 39602″ Length - Two prong zinc-plated, stamped steel with aluminum alloy holder is adjustable by checknut to any angle.

 

LabStock LB71-1 Support Clamp Single Burette Clamp 6 Length

LabStock LB71-1 Support Clamp, Single Burette Clamp, 6″ Length

LabStock LB71-1 Support Clamp, Single Burette Clamp, 6″ Length - Burette clamp is probably the most widely used clamp in the laboratory. Suspension clamp is used for suspending thermometers and other small instruments. The jaws can be rotated. These robust support clamps are all designed to securely fasten to a 1/2″ support stand with a thumb screw. Coated jaws protect fragile burettes or test tubes and open 1/2″ to 1-3/4″. Thermometer clamp suspends thermometers and other small instruments by clamping them in rotatable jaws.

 

Eisco Labs BuretteTest Tube Clamp PVC Coated Round Jaws Opens up to 45mm in Dia

Eisco Labs Burette/Test Tube Clamp, PVC Coated Round Jaws, Opens up to 45mm in Dia.

Eisco Labs Burette/Test Tube Clamp, PVC Coated Round Jaws, Opens up to 45mm in Dia. - Round clamp features pvc dipped steel jaws which open from 15mm to 45mm. The clamp attaches to rods up to 13mm in diameter. Threaded rod and wing nut adjust clamp angle and overall length from 13 to 15cm.

 

uxcell Plastic Laboratory Butterfly Double Spring Type Buret Burette Clamp Clip

uxcell Plastic Laboratory Butterfly Double Spring Type Buret Burette Clamp Clip

uxcell Plastic Laboratory Butterfly Double Spring Type Buret Burette Clamp Clip - Product name burette clamp. Package content 1 x burette clamp. Net weight 115g. Material plastic, rubber. Fit for support stand rod size18 x 14mm/07″ x 055″(lw).

 

Eisco Labs Burette Clamps PVC Round Jaws Classpack of 5

Eisco Labs Burette Clamps, PVC Round Jaws, Classpack of 5

Eisco Labs Burette Clamps, PVC Round Jaws, Classpack of 5 - The clamp attaches to rods up to 13mm in diameter. Threaded rod and wing nut adjust clamp angle and overall length from 13 to 15cm. Eisco burette clamp, pvc round jaws(5) burette clampround clamp features pvc dipped steel jaws which open from 15mm to 45mm.

 

GSC International 4-BC37 Burette Clamp with Coated Jaws Single

GSC International 4-BC37 Burette Clamp with Coated Jaws, Single

GSC International 4-BC37 Burette Clamp with Coated Jaws, Single - Test tube brush is 215cm in total length, the brush section is 100mm in length and 125mm in diameter flask tongs are 250mm in total length, have vinyl coated tips and has a maximum opening of 200mm spatula has both a spoon side and flat side, is a total of 150mm long, and has a maximum width of 20mm crucible tongs are 250mm in length and have a maximum opening of 200mm test tube tongs are 170mm in length and have a maximum opening of 70mm. The clamps jaws have a range of 3/8″ x 1-3/8″. Ring clamp with boss head has and inner diameter of 76mm and an outer diameter of 91mm, the bosshead can accept rods up to 20mm in diameter burette clamp holds burettes with diameters up to 22mm (usually 100ml burettes) and is spring loaded with 100% powder coated parts. Kit contains (1) base, (1) rod, (1) beaker tong, (1) tripod stand, (1) wire mesh for heating, (1) boss head, (1) lab clamp, (1) retort ring with boss head, (1) burette clamp double, (1) test tube holder, (1) test tube stand (z-shape), (1) test tube brush, (1) spatula. Test tube/lab instrument rack will hold up to 17 objects (8) small holes have a diameter of 12mm, (6) medium holes have a diameter of 18mm, and (5) large holes have a diameter of 25mm the rack is powder coated and chemically resistant tripod is cast metal and is 190mm in height and has an inner diameter of 75cm and an outer max diameter of 12cm wire mesh is a square with 12cm sides and a 8cm diameter heating surface.

 

Eisco Labs Acrylic Burette with PTFE Stopcock 25mL Capacity 01mL Graduation

Eisco Labs Acrylic Burette, with PTFE Stopcock, 25mL Capacity, 0.1mL Graduation

Eisco Labs Acrylic Burette, with PTFE Stopcock, 25mL Capacity, 0.1mL Graduation - It has high chemical resistance, and resists moisture, high temperatures, flames, thermal expansion, and ultraviolet (uv) exposure. Clamp not included. Acrylic is lightweight, and resists shattering, impact, and most non-abrasive cleaners including ammonia and strong detergents. 10ml graduation, and is suitable for high school or college students, or ages 14 to 21. Eisco burette is for laboratory use. Ptfe plastic is a strong, low-friction material that has smooth transfer, high surface release, and nonstick properties. The burette is made of acrylic for durability, and has a polytetrafluoroethylene (ptfe) plastic plunger stopcock for resistance to chemicals, moisture, and high temperatures. The burette has 25 ml capacity with 0. Ptfe has low temperature toughness.